安全使用鋸片
 
 
1、 所配設備應具備安全保護裝置，如：防護罩，斷電剎車，過載保護等。
 
Applied machine shall be equipped with safety devices, such as protective cover, power-off brake and overload protector.
 
2、 檢查鋸片有無損壞，齒型是否完整，鋸板是否平整光潔，以及有無其他異常現象，以確保使用安全。
 
Check if the saw blade is scratched, if the edge is complete and if the blade sheet is flat and clean to ensure the safe status.
 
3、 確保機器狀態良好，主軸無變形，無徑跳，軸徑公差為h7。保證鋸片回轉方向與機器主軸回轉方向一致。
 
Ensure the sound condition of the machine including but not limited to no transformed bearing, no track jump and the tolerance is h7. Reversing direction of

blade shall be the same with that of main bearing.
 
4、 法蘭盤內徑與鋸片內徑一致，外徑應不小于鋸片外徑的1/3，并確認其表面平整光潔，無變
 
形，無端跳。保證鋸片內徑與機器軸徑之間無過大間隙，安裝好法蘭盤，裝好定位銷，擰緊螺母。
 
Internal diameter of Flange Plate should be the same with that of the blade. External diameter should be no smaller than 1/3 of external diameter of the

small blade. The surface should be flat and clean without transformation and end jump. Avoid too big gap between the blade and the bearing in terms of

internal diameter. After installation of Flange Plate, set up the positioning pin and fasten the nut.
 
5、 工作時，發現聲音和振動異常、切割面粗糙、或產生異味時，必須立即終止作業，及時檢查，
 
排除故障以免發生意外事故。
 
If any noise, vibration or unsmooth surface or bad smell is detected, please stop the operation immediately and a check should be conducted shortly to avoid

any possible accident.
 
 
 
硬質合金圓鋸片的修磨
 
當鋸片不再鋒利，切斷橫截面粗糙，必須對鋸片進行修磨，否則對切割效果有很大的影響，導致鋸片使用壽命縮短，有以下情況須進行修磨更換處理：
1：使用鋸片的機器耗能顯著增加
2：加工材料時，有明顯崩裂現象
3：合金刀頭的刃口磨損達到0.2MM
鋸片的修磨，應到專業的修磨機器或公司進行修磨，確保鋸片長期高效使用。
歡迎隨時聯系